Modificari - Codari si Adaptari cu VCDS / VAG-Com pentru A4 B8

Removing Seatbelt Chime: (Beep Centura siguranta)

[Select]
[17 - Instruments]
[Coding - 07]
[Long Coding Helper]
Click on each of the Byte numbers in step 3) and you'll see the selectable options below.
Uncheck the box for "Seatbelt Warning active"
[Do It!]
________________________________________
Enabling Gauge Test/Needle Sweep: (Test ace kilometraj si turometru inainte de pornire motor)

[17 - Instruments]
[Coding - 07] -> Long Coding Helper -> Byte 1
Bit 0 - Check the box for "Gauge Test/Needle Sweep active"
________________________________________
Enabling Lap Timer: (Cronometru)

[17 - Instruments]
[Coding - 07] -> Long Coding Helper -> Byte 1
Bit 3 - Check the box for "Lap Timer active"

How Lap Timer works



• Lap Timer is chosen in DIS with button B.
• Press on the top of A to start a Lap Timer session (each time the top of A is pressed a new Lap Timer Session is started, and the old is stopped).
• Press on the bottom of A, and you get a Split Time of the current Lap Timer, continue the Lap Timer by pressing on the top of A - if you press on the bottom of A while Split Time is shown, you will pause the Lap Timer - continue the Lap Timer by pressing on the top of A.
• Press and hold the reset button B for 2-3 sec. and you will get an average result of all Lap Timer which was started.
• Press and hold the reset button B for 2-3 sec. and the Lap Timer will be reset.
________________________________________________

Operating Windows and Sunroof with Remote*:


*Note, the sunroof can only be opened (tilted) with the remote, when activated in MMI (CAR>WINDOW>CONVENIENCE>SUNROOF>ON)
You need to continuously hold the remote button for the function to operate.
[Select]
[46 - Cent. Conv.]
[Coding - 07]
[Long Coding Helper]
Click on each of the Byte numbers in line 3 and you'll see the selectable options :below.
Check the box for "Comfort Operation: Remote Control active"
[Transfer Coding]
[Do It!]

________________________________________

Hidden menu in MMI high (2G): (Only for Navigation equipped cars)
Meniu ascus pt navigatia 2G

[07 - Control Head]
[Adaptation - 10] -> Channel 8
change 0 to 1
Use this hidden menu at your own risk.
Caution: Keep away from the "Bootloader".
________________________________________

Hidden menu in MMI Navi Plus (3G): (Only for Navigation equipped cars)
Meniu ascus pt navigatia 3G

[5F - Information Electr.]
[Adaptation - 10] -> Channel 6
change 0 to 1
Use this hidden menu at your own risk.
Caution: Keep away from the "Bootloader".
________________________________________

Fixing LED shut off when turn sign is on while DRL are active only:
Ledurile nu se mai sting cand semnalizezi

[09 – Cent. Elect.]
[Coding - 07] -> Long Coding Helper -> Byte 3
Bit 2 - LEDs remain at full brightness with parking lights (1 = active)
Bit 7 - Turn off LED-strip DRLs with indicators (1 = active)
________________________________________

Turn off amber side markers (US models Only):

[09 – Cent. Elect.]
[Coding - 07] -> Long Coding Helper -> Byte 10
Submodule 0
Bit 3 - Set to 0 to disable amber side markers (U.S. vehicles)
________________________________________

Headlight washer - duration of wash:
Durata de spalare a farurilor

[09 – Cent. Elect.]
[Security Access - 16]
[Adaptation - 10] -> Channel 6
change to e.g. 500
________________________________________

Disable automatic rear window wipe on the Avant, when windscreen wipers are active and the car is reversing:

[09 – Cent. Elect.]
[Security Access - 16]
[Adaptation - 10] -> Channel 19
change 1 to 0
________________________________________

Headlight washer - times of wash and wipe cycles between each automatic activation:

[09 – Cent. Elect.]
[Security Access - 16]
[Adaptation - 10] -> Channel 26
change to e.g. 10

________________________________________

Headlight washer - time of holding down the washer lever after which headlight washers activate:

[09 – Cent. Elect.]
[Security Access - 16]
[Adaptation - 10] -> Channel 25
change to e.g. 10

________________________________________

Headlight washer - Completely disable the headlight washers:

[09 – Cent. Elect.]
[Security Access - 16]
[Coding - 07] -> byte 20 from 04 to 00

________________________________________

Audi parking system - Switch OFF Speed:

[10 - Park/Steer Assist]
[Adaptation - 10] -> Channel 23
change to 20 (max value in km/h)
________________________________________


Consumption in DIS: (recalculare consum mediu)

[17 - Instruments]
[Adaptation - 10] -> Channel 3
change 100 to xxx (see samples below)
Sample 1 - Calculation based on volume per distance (e.g. l/100km):
DIS: 9,3 l/100 km.
Real: 9,8 l/100 km. (100 * 9,8 / 9,3 = 105,38)
Channel 3 will be changed from 100 to 105
Sample 2 - Calculation based on distance per volume (e.g. MPG):
DIS: 23 MPG.
Real: 24 MPG. (100 * 23 / 24 = 95,83)
Channel 3 will be changed from 100 to 96
________________________________________

DIS with Efficiency Program for MY2010+ (Not a complete Program without the Start/Stop System):

[17 - Instruments]
[Adaptation - 10] -> Channel 77
change 0 to 255
________________________________________


DVD navigation eject lock:

[37 - Navigation]
[Adaptation - 10] -> Channel 68
0 = button active
1 = button inactive (anti-theft)
http://wiki.ross-tech.com/index.php/Audi_A4_(8K)_Navigation
________________________________________

Emergency Brake Flashing Lights:

[46 - Comfort System]
[Coding - 07] -> Long Coding Helper -> Byte 8
Bit 0 – Emergency Brake Flashing via Turn Lights active (1 = active)
Bit 1 – Emergency Brake Flashing via Brake Lights active (1 = active)
________________________________________


Phone voice control:

Not Available for MY2010
[77 - Telephone]
[Coding - 07]
00x0x?0 - The 2nd to last digit should be changed to e.g. 2 (English (UK))
Coding
00?0xx0: MMI System
1 = MMI/Sound System High
2 = MMI/Sound System Standard
00x0?x0: Installation List
9 = Vehicle with MOST-Databus
00x0x?0: Voice Control Language
0 = Voice Control OFF
1 = German (Rest of World)
2 = English (United Kingdom)
3 = French (Rest of World)
4 = Italian (Rest of World)
5 = Spanish (Rest of World)
6 = Spanish (USA)
7 = English (USA)
8 = French (Canada)
9 = Speaker depend Voice Selection
http://forums.audiworld.com/showthread.php?p=23587701
http://wiki.ross-tech.com/index.php/Audi_A4_(8K)_Telephone_Preparation_(MOST)

____________________________________________________________

Passenger Side Mirror Turn-down (while reversing) w/o Memory Seats/Mirrors:

Mirror selector switch must be on right mirror to work:



________________________________________

Activare afisare viteza pe ecran:

56 unit (radio), channel adaptation - 02



________________________________________


Adaptive cruise control default distance:

In cars with adaptive cruise control the default distance (1 to 4) can be changed from the CAR menu. If this menu option is hidden in you car, apparently you can enable it with VAG-COM. From the Auto distance regulation module 13, Adaptation, Channel 7, change 0 to 1, Save. Thanks must also go to Ville_K for this and confirmation of other information here

________________________________________

Enabling/disabling doors locked/alarm armed sound:

It is possible to enable the beep the car makes when locking doors in European models and likely to disable the beep in U.S. models that beep by default (and vice-versa of course). Just make sure you have the latest VCDS/VAG-COM updates installed and check/uncheck the checkbox Anti-Theft-System: Horn Confirmation active in 46 Central Conv., Long Coding, Byte 01, Bit 2. This may require that factory alarm is installed on the car.

You can also enable a dual opening beep by changing the value on adapter channel 63 (in module 46) from 40 to 44 (or, judging by the link/info in the next text, adding 4 to whatever value you have there). (Old text about this: According to an unconfirmed post at motor-talk.de (http://www.motor-talk.de/forum/codierungen-hier-sammeln-t1963013.html?page=57), one can also enable opening dual beeps in addition to a closing beep. The instructions are: "Komfortsystem (Adresse 46) / Anpassung / Zentralverriegelung Funktionen -> zum eingetragenen Wert +4 addieren" which translates to "Comfort System (address 46) / adjust / add central functions -> to the registered value +4".)

________________________________________

Adjust radio Chorus/Concert/Symphony stopping time:

According to unconfirmed post at motor-talk.de, one can adjust this from module 56, adaptation channel 3, from 1 to 99 minutes.
________________________________________

Change MMI 3G splashscreen:

According to unconfirmed post at motor-talk.de (http://www.motor-talk.de/forum/codierungen-hier-sammeln-t1963013.html?page=52), go to MMI 3G hidden menu (see above how to enable it), car, carcodingvehicle, set the desired settings and press Update Splashscreen (according car line), then reset MMI.

________________________________________


Audio CD import with CD-Text support in MMI 3G:

According to unconfirmed post at motor-talk.de (http://www.motor-talk.de/forum/codierungen-hier-sammeln-t1963013.html?page=55), go to MMI 3G hidden menu (see above how to enable it), diagnosis, settings, multimedia import of copy / no ripping to copy / ripping set.

________________________________________

Lower MMI 2G radio volume when reversing with APS Plus:

If your radio volume isn't lowering automatically, add +8 to the stored value in adaptation channel 11 in 07 Control Head.

________________________________________

Coding after retrofitting Xenons in place of halogens:

This is for A4 B8, unknown if completely same for A5/Q5, could be. TS-Tec posts quite useful coding changes for those looking into replacing halogen beams with Xenons (http://www.motor-talk.de/forum/codierungen-hier-sammeln-t1963013.html?page=69). See the link for details and a more readable format, but to summarize here is a translation of what he reports: In 09 - Central Elect. Byte 0 from #69 to #26 (Xenon installed), Byte 2 from #C0 to #D0 (DRL as LED tail lights and one stripe at DRL), Byte 3 from #A7 to #AF (LED-Stripes at Coming / Leaving Home), Byte 14 #5F to #5D (maybe necessary for the high beam switch), Byte 15 #5F to #5D (maybe necessary for the high beam switch). Cars with beam assistant: In 20 - Beam Assistant Byte 0 of #01 to #02. Note that these are byte values, not individual bits. He also mentions: "BCM1 Byte 6 Bit 3 means LED at CH/LH", CH/LH = Coming Home / Leaving Home.


________________________________________

Daytime running lights behaviour:

Daytime running lights (DRLs) behave differently in different markets, for example the front LED light strips that accompany Xenon lights turn off or dim in some markets when blinking/signalling. Aerodave on A5OC.com has researched this and posted his experiences here: http://www.a5oc.com/forums/showthread.php/have-solved-drl-2468/index.html. In short, he reports that changing Central Electronics 09, Submodule 0 (Master Cent. Elec. box, rather than a slave module), Byte 3 (fourth from the left), Bit 7 (first bit from the left in the binary representation, bottom check box in the VAG-COM long coding helper) is the key. If set to 1, setting it to 0 makes the DRLs stay on when signalling. Thanks to Aerodave and please see the full thread for more!

Aerodave - thanks! - sent this great list of additional bits you can toggle and turn to change the DRL behaviour.

For submodule 0:

Byte 02
bit 0 -
bit 1 - front side markers as DRL
bit 2 - headlights as DRL
bit 3 - fog lights as DRL
bit 4 - LED strip as DRL
bit 5 -
bit 6 - side markers as DRL
bit 7 - tail lights as DRL

Byte 03
bit 0 -
bit 1 -
bit 2 - LEDs remain at full brightness with parking lights
bit 3 -
bit 4 - Turns off DRLs when checked
bit 5 -
bit 6 -
bit 7 - Turn off LED-strip DRL with turn signal (dim LED if front side marker also selected as DRL)

Byte 10
bit 3 - Set to 0 to disable amber side markers (U.S. vehicles)
________________________________________


To disable the "one more wipe after some time" function in the window washer:

In module 09, coding, wiper control sub-module (WWS), long coding wizard, change byte 1, bit 3.

________________________________________

Enable TPMS:

The ABS unit exist in two versions (which can be found on a label in the service book or in the trunk where the spare wheel is located)
• 1AT - ESP ready for TMPS
• 1AS - ESP not ready for TPMS
The pattern seen until now, shows that 1AS won't work.

Known to work on ABS units:
Part No: 8K0 907 379 AH
Component: ESP8 quattro H04 0230

Part No: 8K0 907 379 S
Component: ESP8 quattro H04 0210

Part No: 8K0 907 379 R
Component: ESP8 front H04 0210

Part No: 8K0 907 379 AQ
Component: ESP8 front H03 0210
The retrofit:

Enable the TPMS MMI item (the menu item will be grayed out - disabled):

MMI high (MMI 2G):
Quote:
[07 - Control Head]
[Adaptation - 10] -> Channel 01
add 16 to the existing value



MMI Plus (MMI 3G):
Quote:
[5F - Information Electr.]
Not know yet how to enable the TPMS menu item with VCDS....

BUT can be enabled through the "hidden menu":
- select 'RDK' in 'car/cardevicelist'
- put 'Tires Air Pressure Control' on 5 in 'car/carmenuoperations'
MMI basic (non-MMI - 2G) (symphony/concert radio):
Quote:
[56 - Radio]
[Coding - 07] -> Long Coding Helper -> Byte 8

Bit 6 - TPMS Settings active
MMI need to be restarted.


Then enable the 'connection' between ABS/ESP and the TPMS MMI menu item (the menu item get activated), by setting:
Quote:
[03 - ABS Brakes]
[Security Access - 16] (probably with login code: 61378)
[Coding - 07] -> Long Coding Helper -> Byte 1

Bit 3 - Tire Pressure Monitoring (PR-7K6) active (1 = active)



Then the TPMS need to be enabled in the Instrument Cluster:
Quote:
[17 - Instruments]
[Coding - 07] -> Long Coding Helper -> Byte 4

Bit 0 - Tire Pressure Monitoring (TPMS) installed (1 = active)

The TPMS MMI menu then look like this:


After the 'teach-in process', I lowered the tyre pressure twice - first by 0.2 bar, and then by another 0.2 bar (it is not a real life scenario, but it was working) - I drove 10 to 15 km on a motorway, no error with the first 0.2 bar, but with the second I got this warning in my DIS almost right away after about 3 km:


The message "Please check tyre pressure (xxxx)" will flash a couple of times together with a warning sound - after that only the small tyre symbol on the top will be shown, and it will continue to flash, until the system has been reset (tyre pressure fault has been solved).

The teach-in process:
The teach-in process is performed once after the SET key is pressed for the low tyre pressure indicator.
During the next trip, the control unit saves the measured wheel speeds and the vibration characteristics of the wheels in various vehicle operating states. The vehicle operating states are basically defined by the following parameters: vehicle speed, steering angle, transverse acceleration and yaw velocity. These teach-in values subsequently make up the target data which is used for monitoring.
After approximately 10 minutes of driving, it is already possible to detect a breakdown (rapid loss of pressure). Approximately 60 minutes of driving are required to detect diffusion loss (slow loss of pressure).
The following displays are possible:
• In the event of a rapid loss of pressure at a single wheel (tyre damage), the red warning lamp is activated. If the vehicle a driver information system, an additional text display appears indicating the position of the wheel affected.
• In case of slow loss of pressure, which occurs gradually at multiple wheels due to diffusion, the red warning lamp is also activated. In this case, the optional text display appears but no positional information is given. The displays are activated when the tyre pressure drops below an a coded minimum value.
• When system faults are detected, the yellow warning lamp is activated.

___________________________________________________________

Battery and oil level for radio Chorus/Concert/Symphony:

B8_Jim reports at http://www.audizine.com/forum/showthread.php?278256-Cool-VAG-COM-codes/page12 that by going to 56 - Radio, Adaptation, Car menu Options 1 add +16 to the value there to enable battery level in the CAR menu. He also suggests to try the value 65535 for all options in the menu, including oil level if your hardware supports it.

Lightning menu
1. MMI high (2G):
Code:
Enable the Interior lighting (extended) MMI item:
[07 - Control Head]
[Adaptation - 10] -> Channel 1
add 2 to the existing value
MMI Plus (3G):
Code:
[5F - Information Electr.]
Not know yet how to enable the Interior lighting menu item with VCDS....

BUT can be enabled through the "hidden menu":
- select 'Interior Light' in 'car/cardevicelist'
- put 'Interior light' on 1 in 'car/carmenuoperations'
MMI basic (non-MMI - 2G) (symphony/concert radio):
Code:
[56 - Radio]
[Coding - 07] -> Long Coding Helper -> Byte 8

Bit 7 - Interior Light Settings active - (1 = active)
Then enable the 'connection' between Cent. Elect and the Interior light MMI menu item (the same on all systems):
Code:
[09 – Cent. Elect.]
[Coding - 07] -> Long Coding Helper -> Byte 16

Bit 6 - Set this bit manually to “1” - (1 = active)
If the menu item is still grayed out - then a restart of MMI is required now...

___________________________________________________

Se aprinde proiectorul odata cu semnalizarea.

1. Previously I posted that on module 9 Byte 4 Bit 0 would turn on your left hand fog light with headlights. I was wrong. What I discovered tonight was if you have this bit enabled and your headlights on BUT NOT your fog lights, it will fade in your left or right fog light then fade it off with your turn signal.

So you put your right turn signal on, the right fog light fades on. When you turn the signal off it fades off. It's kind of neat. Of course you have to meet those exact requirements for it to work.


________________________________________________

Changing default Audi Drive Select mode:

It has been reported (http://www.motor-talk.de/forum/endlich-codierungen-drive-select-t2593674.html and http://www.audizine.com/forum/showthread.php?349092-VCDS-coding-of-Audi-Drive-Select-default-setting) that by adjusting all these four adaptation channels, one can change the default Audi Drive Select mode from auto to any of the other three modes: 09 – Cent. Elect. - Security Access - 16 - Adaptation - 10 - Channels 63, 64, 65 and 66. Set the channels (all of them) to one of these numbers: 1 = Comfort, 2 = Auto (default), 3 = Dynamic, 4 = Individual. Thanks to schneidfried!

Limited Audi Drive Select individual mode also for cars without Audi Drive Select:

C99 reports at A5OC.com (http://www.a5oc.com/forums/showthread.php/vag-com-change-10568/index.html) that even cars without Audi Drive Select buttons can be coded to adjust engine response and automatic gear-box, as well as Servotronic steering, like an ADS (without dynamic steering or dynamic dampening) would. (See also AudiZine.com: http://www.audizine.com/forum/showt...Audi-Individual-Drive-Select-VAGCOM&p=5020059) First 09 - Central Electric is coded to "Charisma engine only" byte 7, bit 5, change 0 to 1 (you may also have to change byte 7 bit 2 as well), byte 8, bit 2, change 0 to 1 and byte 17, bit 7, change 0 to 1. In byte 8 bit 3, 4 and 5 from 0 to 1 will respectively switch steering, suspension and sports differential modes on in addition to the engine mode, although the latter two modes are undoubtedly of no use without such hardware in the car. Byte 7, bit 4 is apparently for active steering, again probably of use only if such hardware is in the car. Then 09 - Central Electric, Security Access - 16, Adaptation - 10, change channels 63 to 66 to value 4 (individual mode). (See here for more discussion on these codes: http://www.a5oc.com/forums/showthread.php/vag-com-change-10568/index2.html)

Getting the Audi Drive Select individual option appear in CAR menu (MMI cars only) you may need to access the hidden menu to enable "Charisma" (the code-name for Audi Drive Select), see way above in this article on how to enable and access the hidden menu in MMI 2G and MMI 3G. MMI 2G: In hidden menu menu go to Diag settings, Car menus maske, check Charisma and go down to Accept changes. MMI 3G: In hidden menu, go to "car", select “cardevicelist”, scroll down and check Charisma. Go back, and still in the "car" hidden menu, select “carmenuoperation”. Scroll down to Charisma, change from 0 to 1. On both MMIs then reset the MMI. For cars without MMI (e.g. with radio Concert/Symphony) and thus without the Audi Drive Select individual menu it is probably worth trying setting Comfort or Dynamic modes directly (in the channels 63-66) using the VAG-COM coding above in "Changing default Audi Drive Select mode" to see if there is change in engine, steering and auto-transmission.

________________________________________________

Audi parking system - Change deactivation Speed of Camera

[10 - Park/Steer Assist]
[Adaptation - 10] -> Channel 23 Change to 20 (max value in km/h)

________________________________________________

Auto Release Brake without Seatbelt On

This will allow you to move your car and have the brake release without your seatbelt on.
[53 - Parking Brake]
[Security Access - 16] (Enter code presented by program)
[Adaptation - 10] -> Channel 7 change 1 to 0

_________________________________________________

Release Parking Brake without putting foot on Brake

This will release your parking brake without moving or putting your foot on the brake. There is lots of potential for accidents by disabling this feature so please act accordingly.
[53 - Parking Brake]
[Security Access - 16] (Enter code presented by program)
[Adaptation - 10] -> Channel 4 change 1 to 0

_________________________________________________

Disable "Please Release parking brake" message while in gear

[53 - Parking Brake]
[Security Access - 16] (Enter code presented by program)
[Adaptation - 10] -> Channel 3 change 0 to 1

_________________________________________________


Disable window lock

This will disable the wiondow lock out button on the drivers door.
[42 - Door Elect, Driver]
[Coding - 07] -> [Long Coding Helper] -> Byte 2 Bit -> 2 Change 0 to 1

_________________________________________________________

Incremental drivers window up and down

Not sure how useful this will be but it makes the window go up and down only a few inches with each button press.
[42 - Door Elect, Driver]
[Coding - 07] -> [Long Coding Helper] -> Byte 3 Bit -> 2 Change 0 to 1

__________________________________________________________

Disables one touch down - On Drivers Window

[42 - Door Elect, Driver]
[Coding - 07] -> [Long Coding Helper] -> Byte 3 Bit -> 3 Change 0 to 1

__________________________________________________________

Disables one touch up - On Drivers Window

[42 - Door Elect, Driver]
[Coding - 07] -> [Long Coding Helper] -> Byte 3 Bit -> 7 Change 0 to 1

__________________________________________________________

Disable one touch up and down on drivers window

[42 - Door Elect, Driver]
[Coding - 07] -> [Long Coding Helper] -> Byte 5 Bit -> 1 Change 0 to 1

__________________________________________________________

Disables all Windows up

[42 - Door Elect, Driver]
[Coding - 07] -> [Long Coding Helper] -> Byte 7 Bit -> 4 Change 0 to 1

__________________________________________________________

Disables Drivers Side Rear Window Down

42 - Door Elect, Driver]
[Coding - 07] -> [Long Coding Helper] -> Byte 7 Bit -> 0 Change 0 to 1

_____________________________________________________
PT CELE MAI BUNE REZULTATE ESTE NECESAR UN CABLU VAG-COM ORIGINAL. UNELE CODARI NU VOR MERGE CU UN CABLU AFTERMARKET. FIECARE FACE ACESTE CODARI SI ADAPTARI PE PROPRIA RASPUNDERE.

Adjust LED Brightness

This will allow you to change the intensity of the LED's when your headlights are on. By default the LED's are only 8-9% or brightness.
[09–Cent.Elect.]
[Security Access-16](enter security code. One of the default codes is- 20113)
[Adaptation-10]->Channel3
Enter new value for LED brightness i.e. "100" If you want LED's at 100%.
Values bellow 5 turns the LED's off and generates an error code and warning in DIS .

 

Cu ajutorul colegului strumfyspm s-au mai adaugat cateva link-uri referitor la adaptari cu VCDS pentru A4 B8.

1. Codari Vag-Com complete:
http://www.stemei.de
Chrome pentru traducere. E full coding Vag-Com

2.Modificari A4 B8
http://audienthusiasts.com/index.html

3.Adaption&Codding
http://www.audi-portal.com

 

Salut,

Pentru activarea functiei cornering trebuie sa urmezi cu VCDS pasii de mai jos:
[09 – Cent. Elect.] => [Coding - 07] => [Long Coding Helper] => Byte 4 Bit 0 Change 0 to 1
Aceasta functie se activeaza numai pentru o viteza max. de aprox. 40 km/h

Pentru aprinderea proiectorului dreapta sau stganga in functie de cum virezi sau semnalizezi, procedeaza in felul urmator:
09 [Centr. Elect.] > 07 [Coding] > In Octetul 4 schimba bitul 0 din valoarea 0 in valoarea 1 (cred ca stii ca bitul 0 este primul din dreapta).
Aceasta functie este valabila numai cand este aprinsa faza de intalnire (faza scurta), iar cand cuplezi in marsalier nu mai este activa.

 

Salutare, pentru activarea functiei de cornering trebuie facuta setarea cu farurile aprinse sau este conditionata de o anumita optiune a masinii ?
Multumesc

 

In timpul setarii functiei de cornering cu Vag-Com, nu este necesar ca farurile sa fie aprinse si nici nu depinde de o anumita optiune a masinii. Dupa activarea functiei cu Vag-Com, aceasta va fi activa numai daca faza scurta este aprinsa si pana la o anumita viteza (30-40 km/h... parca). Nu functioneaza la mersul inapoi.

 

Multumesc pentru raspuns. Am incercat activarea functiei si nu am reusit , ma impotmolesc la faza cu cu bit4 nu stiu unde trebuie schimbata valoarea 0 cu 1

 

mi se pare aiurea aceasta functie deoarece nu functioneaza decat daca semnalizezi... si nu ca la passat in functie de pozitia volanului

 

anarchy: Functioneaza si la rotirea volanului (dupa ce ai rotit minim 1/2 de tura);
rominika: Am scris in postul #92 cum se procedeaza. Mai clar de atat nu cred ca se poate.

 

n-am sesizat sa se aprinda proiectorul daca nu semnalizez...
voi analiza acest aspect mai atent.

 

Am gasit postul si o poza care sint destul de clare insa cel cu vag-ul nu a avut inca timp de mine, multumesc

 

Am rezolvat cu functia cornering multumesc de ajutor

 

Salutare,

Am si eu o mica rugaminte sau mai exact cerinta: pe portiera soferului exista un buton care blocheza geamurile din spate si nu le mai poti actiona decat de la sofer.

Exista vreo codare sa fie si cel din dreapta fata inclus (adica sa nu poata fi actionat decat de pe partea soferului) ?

Ma refer la A4 B8.

 

strumfy nu exista ! e doar blocare geamuri spate ! (child lock).
fiind child lock => copilul nu are ce cauta pe locul din fata !


stie cineva cum se fac urmatoarele ?

- sa stingi complet ecranul e la navi cand conduci noapte la drum lunga, dar muzica sa ramana pornita in background

- cand repornesti masina sa porneasca incalzirile in scaun pe 0 si nu pe ultima treapta folosita anterior

- sa se incrementeze numarul de incercari de a deschide o usa blocata (momentan la a 2-a se deschide)

 

Robytza ecranul se stinge din Mmi. Eu il sting in mod curent iar muzica ramane binenteles. Cu incalzirea in scaune nu am teatat inca. Cu geamurile si cu ploaia merge dar trebuie sa lasi stergatoarele mereu pe auto ca sa functioneze. Inclusiv cand incui masina. Ultima habar nu am ce intrebi

 

elexista vreun shortcut pentru a stinge ecranul de la mmi ? gen apasarea lunga a unui buton ?

 

Durata iluminare

Stie cineva cum pot modifica timpul de stingere al plafonierei cand contactul nu este pus(in pozitia accesorii).
Mai clar deschid usa, intru in masina, inchid usa iar plafoniera se stinge dupa 10-20 secunde iar eu vreau sa micsorez acest timp.
Cu motorul pornit sau contactul pus lumina se stinge odata cu inchiderea usii fara nici o intarziere.

 

Din cate stiu eu nu se poate modifica ceea ce vrei tu din VAG-COM. Mai asteapta si alte pareri. Bafta

 

????

salut..dupa ce s-au facut niste activari cu vag-ul si nu prea imi sunt de folos,stie cineva cum pot reveni la setarea anterioara,adica cea de fabrica????msk

 

le scoti in ordinea inversa in care le-ai bagat...
nu exista ceva automatizat si chiar daca ar exista, depinde de calculatorul pe care esti...

 

Stie cineva ce trebuie sa modific (pt A4 B8 sedane) sa mi se aprinda si stopurile de ceata cand se apasa frana? Vazusem la o Octavia si ma gandeam ca se poate si la Audi..
Ma gandesc ca ar fi folositor si pentru ceilalti participanti la trafic..se vede mai bine!

Si eventual daca stie cineva ce trebuie modificat pentru momentul in care ai aprinse proiectoarele si dai faza lunga sa se aprinda alternativ!